FOHERE QF-150 Manual Pasta Machine Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
The FOHERE QF-150 is a hand-crank pasta machine in red: carbon steel rollers in a stainless steel body, a seven-step dial from 0.5 mm to 3 mm, and a cutter head with a 1.5 mm narrow cut and a 6.5 mm wide cut. FOHERE calls it 3-in-1 because it gives sheets, spaghetti-style strands and fettuccine. A G-clamp and a non-slip base hold it down. It weighs only 2.56 lb, at 7.87 x 7.68 x 5.91 in. Verdict: the QF-150 is a low-cost starter roller for occasional pasta and dumpling wrappers, with a usefully thin 0.5 mm setting; its light weight means the clamp matters. The listing leaves the clamp's maximum table thickness as an unfilled placeholder, so measure your counter edge and ask the seller. FOHERE's listing and specs are the basis here; we have not used the machine.
What stands out
- Seven settings, 0.5 mm to 3 mm
- Cutters: 1.5 mm narrow and 6.5 mm wide
- G-clamp plus non-slip base
- Light at 2.56 lb
Who it fits
Good fit for
Beginners and occasional cooks who want sheets, thin strands, fettuccine and dumpling wrappers from a small, low-cost roller.
Who should skip it
Cooks who make pasta weekly in big batches, or who want a heavier machine or a motor option.
Verdict: A small, light starter roller with a thin 0.5 mm setting.
FOHERE QF-150 specs from the listing
QF-150 thickness: 7 settings, 0.5-3 mm
0.5 mm suits dumpling skins and thin sheets.
QF-150 cutters: 1.5 mm and 6.5 mm
Thin strands and fettuccine.
QF-150 body: stainless steel, carbon steel rollers
Listed as rust-resistant.
QF-150 size: 7.87 x 7.68 x 5.91 in, 2.56 lb
Small enough for a drawer.
How the FOHERE QF-150 is built
The QF-150 pairs carbon steel rollers with a stainless steel body finished in red, a numbered dial for the seven settings and a two-cut head on the same frame. A G-clamp locks it to a table, and FOHERE adds a non-slip base. The clamp line in the listing reads "up to [insert thickness] inches", so the real limit is not given. At 2.56 lb it is much lighter than the YASHE machine that shares the QF-150 code.
Using the FOHERE QF-150
Clamp the QF-150 to a table edge, run a flattened piece of dough through the widest setting a few times, folding it each time, then step down to the thickness you want. Stop at 0.5 mm for dumpling wrappers or around the middle settings for lasagna. Move the sheet to the cutter and crank it through the 1.5 mm or 6.5 mm side.
Keep the QF-150 rollers dry; brush off flour once they are dry instead of rinsing.
Before you buy the FOHERE QF-150
Choose the FOHERE QF-150 if you want a light, cheap roller with a 0.5 mm setting and two cuts. Choose the YASHE QF-150 if you want a sturdier 6.39 lb machine that goes down to 0.3 mm with 2 mm and 6.5 mm cutters. Choose the electric FOHERE MMD150-II if cranking is the part you dislike.
Check before you buy
- Counter edge measured for the QF-150 clamp
- Two cuts (1.5 and 6.5 mm) are enough
- Dry-brush cleaning for the QF-150
- Batch size suits a light roller
The product at a glance
FOHERE 3-in-1 Manual Red Pasta Maker
Best for: Occasional pasta and dumpling cooks
- Operation Mode
- Manual crank
- Thickness Settings
- 7
- Cut Widths
- 1.5 mm, 6.5 mm
- Housing Material
- Stainless steel
- Roller Material
- Carbon steel
- Pasta Type
- Spaghetti, Fettuccine, Lasagna, Dumplings
View on Amazon: FOHERE 3-in-1 Manual Red Pasta Maker Affiliate link
The FOHERE QF-150 is a red hand-crank pasta machine with seven settings from 0.5 to 3 mm, 1.5 mm and 6.5 mm cutters and a G-clamp. It weighs 2.56 lb.
Pros
- QF-150 rolls down to 0.5 mm
- QF-150 cuts strands and fettuccine
- QF-150 is light and compact
Cons
- QF-150 clamp limit left blank
- QF-150 is light for heavy dough
Good fit if
- You want a low-cost starter roller
Skip if
- You roll big batches every week
Verdict: A light starter roller with a thin setting.
Specifications side by side
| Spec | FOHERE 3-in-1 Manual Red Pasta Maker |
|---|---|
| Operation Mode | Manual crank |
| Thickness Settings | 7 |
| Cut Widths | 1.5 mm, 6.5 mm |
| Housing Material | Stainless steel |
| Roller Material | Carbon steel |
| Pasta Type | Spaghetti, Fettuccine, Lasagna, Dumplings |
| Color | Red |
| Dimensions | 7.87 × 7.68 × 5.91 inches |
| Weight | 2.56 pounds |
| Size | Standard |
| Model | QF-150 |
Frequently asked questions
How many settings does the FOHERE QF-150 have?
Seven, from 0.5 mm to 3 mm.
What widths does the QF-150 cut?
The QF-150 cuts 1.5 mm strands and 6.5 mm fettuccine.
Is the FOHERE QF-150 the same as the YASHE QF-150?
No. They share a model code, but the YASHE weighs 6.39 lb, goes to 0.3 mm and cuts 2 mm and 6.5 mm.
How does the QF-150 attach to a table?
With a G-clamp; FOHERE also lists a non-slip base.
How heavy is the FOHERE QF-150?
2.56 lb.
