Brass Pasta Presses and Dies: 6 Picks Compared
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
Brass shows up on pasta presses and dies rather than whole machines, so this list covers both. Our top pick is the Torkio OK Leonardo press: made in Italy, with five 4 cm brass dies and a suction base with a vacuum gauge that needs no vise. The Torchio Bigolaro is the traditional brass bench press, the tortiglioni and Rosinella Fusilli 4P dies fit Häussler PN100, Emma and Lillodue extruders (the Rosinella is the cheapest), a 15 mm maccheroni die fits TR70 professional machines, and Pastidea's YS kit brings brass-type inserts to Philips. Brass ravioli stamps were removed because they are hand tools, not pasta makers, as were two TR95 dies with one-line listings. The comparison relies on listing text; we have not used these tools.
Our top pick: Tagliapasta Manual Pasta Press with 5 Brass Cutters.
Quick picks
The best fit for you
- Brass-die pasta with no extruder Tagliapasta Manual Pasta Press with 5 Brass Cutters Torkio OK Leonardo, 5 dies.
- A traditional bench press Bottene Torchio Bigolaro Hand Press Pasta Maker Torchio Bigolaro.
- Tortiglioni on a Häussler Tortiglioni Die Brass for Häussler PN100, Emma, Lillodue PN100110, 59 mm.
- The cheapest brass die Rosinella 9 mm Fusilli 4P Brass Die Rosinella Fusilli 4P.
- A TR70 professional extruder Die Brass Maccheroni Striped 15 mm for TR70 Sela La Pastaia Corngold Avancini Omegaone 15 mm maccheroni rigati.
- Brass on a Philips Pastidea Bronze and POM Pasta Disc Set Pastidea YS KIT6.
Our 6 picks
Tagliapasta Manual Pasta Press with 5 Brass Cutters
Best for: Cooks who want rough, sauce-holding pasta
- Material
- Brass (what this guide is about)
- Housing Material
- Enamelled die-cast aluminium
- Operation Mode
- Manual
- Weight
- 3.26 pounds
View on Amazon: Tagliapasta Manual Pasta Press with 5 Brass Cutters Affiliate link
The Torkio OK Leonardo from Tagliapasta is a manual fresh pasta press made in Italy with five brass dies of 4 cm diameter: pappardelle, square spaghetti, tagliolini, spaccatelli and a fifth shape. The body is enamelled die-cast aluminium with an aluminium ferrule and a plastic propeller, and a suction cup with a vacuum gauge holds it on any smooth surface without a vise. It weighs 3.26 lb; stock was low. A cheaper two-die version (paccheri and casarecce) uses the same press.
Pros
- Five brass dies with the Torkio press
- Suction cup with a vacuum gauge
- Italian-made Tagliapasta body
Cons
- Torkio needs arm power to press
- Low stock on the five-die set
Good fit if
- You want brass-die pasta without an electric extruder
Skip if
- You want a machine that kneads the dough
Verdict: The Torkio OK Leonardo is the brass-die press for home cooks.
Bottene Torchio Bigolaro Hand Press Pasta Maker
Best for: Traditional Venetian cooks
- Operation Mode
- Manual crank
View on Amazon: Bottene Torchio Bigolaro Hand Press Pasta Maker Affiliate link
The Torchio Bigolaro is a brass hand-crank press for the Venetian bigoli tradition, supplied with four dies: tagliatelle, tagliolini, bigoli and gargati. It clamps to a table or bench, which you provide, and the dies screw on from below for quick changes. The listing gives no weight or size; stock was low and it is the most expensive pick.
Pros
- Brass Bigolaro body and four dies
- Bigoli and gargati shapes
- Bottom-screw die changes
Cons
- Most expensive brass option
- Needs your own bench or table
Good fit if
- You want a traditional bench press for bigoli
Skip if
- You want a compact counter tool
Verdict: The Torchio Bigolaro is the heirloom brass press.
Tortiglioni Die Brass for Häussler PN100, Emma, Lillodue
Best for: Tortiglioni fans with a PN100
- Material
- Brass (what this guide is about)
View on Amazon: Tortiglioni Die Brass for Häussler PN100, Emma, Lillodue Affiliate link
This brass tortiglioni die (PN100110) fits Häussler PN100, Emma and Lillodue extruders directly, with no adapter, and measures 59 mm across. The seller explains that brass dies give a rougher, grippier surface that holds sauce and spices, and recommends durum wheat semolina. Stock was low.
Pros
- Tortiglioni die fits PN100 with no adapter
- 59 mm die diameter stated
- Semolina recipe advice
Cons
- PN100-format machines only
- Low stock on the PN100110
Good fit if
- Your extruder is a PN100, Emma or Lillodue
Skip if
- You own a Philips
Verdict: The PN100110 is the Häussler tortiglioni die.
Rosinella 9 mm Fusilli 4P Brass Die
Best for: Häussler owners
- Material
- Brass (what this guide is about)
- Pasta Type
- Fusilli
View on Amazon: Rosinella 9 mm Fusilli 4P Brass Die Affiliate link
The Rosinella Fusilli 4P is a 9 mm brass die for Häussler PN100, Emma and Lillodue extruders and the lowest-priced brass pick. Its listing is a single line, so there are no cleaning or output notes. A 3P 10 mm version is also sold.
Pros
- Cheapest brass die here
- 9 mm four-start fusilli
- Fits PN100, Emma, Lillodue
Cons
- Single-line Rosinella listing
- Häussler machines only
Good fit if
- You want fusilli on a Häussler extruder
Skip if
- You want care instructions
Verdict: The Rosinella 4P is the low-cost brass fusilli die.
Die Brass Maccheroni Striped 15 mm for TR70 Sela La Pastaia Corngold Avancini Omegaone
Best for: Small pasta shops
- Material
- Brass (what this guide is about)
View on Amazon: Die Brass Maccheroni Striped 15 mm for TR70 Sela La Pastaia Corngold Avancini Omegaone Affiliate link
This brass die makes striped maccheroni 15 mm wide on TR70-format professional extruders: Sela, La Pastaia, Korngold, Avancini and Omegaone. The seller recommends durum semolina with cold water or egg, kneaded 8-10 minutes to a moist, crumbly dough, and says gluten-free pasta is possible. Stock was low.
Pros
- 15 mm striped maccheroni
- Fits TR70 Sela, La Pastaia, Korngold and others
- Dough recipe in the listing
Cons
- For professional TR70 machines only
- Priciest of the dies
Good fit if
- You run a TR70-format extruder
Skip if
- You cook on a home Philips
Verdict: The TR70 maccheroni die is the brass pick for small producers.
Pastidea Bronze and POM Pasta Disc Set
Best for: Philips owners who want rough pasta
- Pasta Type
- Gnocchi, Fusilli
- Dimensions
- 8.86 × 4.92 × 2.36 inches
- Weight
- 1.76 pounds
View on Amazon: Pastidea Bronze and POM Pasta Disc Set Affiliate link
The Pastidea YS KIT6 brings brass to Philips Avance and 7000 Series machines: a POM holder with six bronze (brass, per Pastidea) inserts made in Italy, including maccherone rigato, fusilli A3 8.5 mm, casarecce and Neapolitan gnocchi. It does not fit the Viva, 5000 Series or HR2484 and is not dishwasher safe. 1.76 lb; low stock.
Pros
- Brass-type inserts for a Philips
- Six short shapes in the YS kit
- Made in Italy
Cons
- Not for the Viva
- Hand wash only
Good fit if
- You own an Avance or HR2660 and want brass-cut pasta
Skip if
- You own a Viva
Verdict: The YS KIT6 is the brass upgrade for Philips extruders.
Specifications side by side
| Spec | Tagliapasta Manual Pasta Press with 5 Brass Cutters | Bottene Torchio Bigolaro Hand Press Pasta Maker | Tortiglioni Die Brass for Häussler PN100, Emma, Lillodue | Rosinella 9 mm Fusilli 4P Brass Die | Die Brass Maccheroni Striped 15 mm for TR70 Sela La Pastaia Corngold Avancini Omegaone | Pastidea Bronze and POM Pasta Disc Set |
|---|---|---|---|---|---|---|
| Operation Mode | not stated | Manual crank | not stated | not stated | not stated | not stated |
| Housing Material | Enamelled die-cast aluminium | not stated | not stated | not stated | not stated | not stated |
| Pasta Type | not stated | not stated | not stated | Fusilli | not stated | Gnocchi, Fusilli |
| Material | Brass | not stated | Brass | Brass | Brass | not stated |
| Weight | 3.26 pounds | not stated | not stated | not stated | not stated | 1.76 pounds |
| Dimensions | not stated | not stated | not stated | not stated | not stated | 8.86 × 4.92 × 2.36 inches |
| Color | Press + 5 Brass Cutters | Brass | not stated | not stated | not stated | not stated |
| Model | TP-TO2021-TO05-TO07-TO08-TO16-TO17 | not stated | PN100110 | PN100222 | ohne Angabe | HR2355MF002YS-KIT6 |
If your workshop projects call for precise, repeatable holes rather than pasta shapes, our comparison of the best drill presses with fence covers that equipment separately.
Buying brass pasta tools
-
Match the format
Dies are machine-specific: PN100 for Häussler, TR70 or TR95 for professional extruders, Pastidea holders for Philips.
-
Dough
Brass dies work best with durum semolina dough that is moist but crumbly, per the die sellers.
-
Care
Do not put brass in the dishwasher; let dough dry and brush it out.
-
Press or extruder
A hand press like the Torkio needs no motor but takes arm effort; an extruder does the pushing.
Frequently asked questions
Is bronze the same as brass for pasta dies?
Sellers use the words interchangeably; Pastidea describes its inserts as bronze (brass).
Do brass dies fit a Philips pasta maker?
Only with a holder made for it, like Pastidea's kits. Häussler and TR70 dies do not fit.
Can I wash brass dies in the dishwasher?
No. Brush out dried dough instead.
Why are brass ravioli stamps not here?
They cut filled pasta by hand and cannot shape dough on their own, so they are tools rather than pasta makers.





